హుక్ రకం షాట్ బ్లాస్టింగ్ మెషీన్ యొక్క సంస్థాపన మరియు పరీక్ష యంత్రానికి జాగ్రత్తలు ï¼ˆä¸ ï¼

2021-06-03

దిహుక్ రకం షాట్ బ్లాస్టింగ్ మెషిన్సాధారణంగా పెద్ద రూపాన్ని కలిగి ఉంటుంది మరియు చిన్న పరికరాల కంటే సంస్థాపనా విధానం చాలా క్లిష్టంగా ఉంటుంది. తరువాతి పరికరాల సాధారణ ఆపరేషన్ను నిర్ధారించడానికి సరైన సంస్థాపన మరియు పరీక్ష యంత్రం కీలకం. నైపుణ్యం లేని ప్రారంభ కార్యకలాపాల విషయంలో, వినియోగదారులు సంబంధిత సిబ్బంది సూచనలను ఖచ్చితంగా పాటించాలి లేదా సూచనలను సూచించాలి. అనధికార ఆపరేషన్ సులభంగా కోలుకోలేని నష్టాన్ని కలిగిస్తుందిహుక్ షాట్ బ్లాస్టింగ్ మెషిన్. దిshot blasting machine manufacturer has sorted out the precautions for installation and test machine to share with you. I hope it will be helpful to users who use the device for the first time.
1. Installation. దిహుక్ రకం షాట్ బ్లాస్టింగ్ మెషిన్ is installed and debugged in the production plant and disassembled into several parts before being transported to the user site for installation. Although there is no pit, the foundation must be firm, the anchor bolt holes must be standardized, and the chamber body must be adjusted. After the second irrigation, the anchor bolt nuts can be tightened after solidification. After the chamber body is fixed, the various parts can be installed. దిprecautions for the installation and debugging of the relevant components are introduced below.
1. షాట్ బ్లాస్టింగ్ పరికరం:
దిshot blasting device has been installed on the chamber body before leaving the factory. Please pay attention to the problems to be debugged before use. Check whether the fixed positions of the blade, the pill wheel, the directional sleeve, and the guard plate are accurate and firm, and check whether the direction of rotation is correct after power on. Then adjust the position of the directional sleeve opening. Theoretically, the angle between the front edge of the directional opening and the front edge of the blade throwing position is about 900. After fixing the position of the directional sleeve, the position of the projectile belt can be detected by hanging Place a steel plate or wooden board on the position of the workpiece facing the exit of the shot blasting machine, start the shot blasting machine, put a small amount (2-5kg) of projectiles into the blasting tube, and then stop, check whether the hit position on the steel plate is suitable for the needs, such as Close the window of the bias-adjustable directional sleeve downwards, and vice versa, until it fits, and note the position of the directional sleeve opening as a basis for future replacement of the directional sleeve.
2. హాయిస్ట్ మరియు స్క్రూ కన్వేయర్:
ఎగురుతున్న బకెట్ మరియు స్పైరల్ బ్లేడ్లు సరైన దిశలో నడుస్తున్నాయో లేదో తనిఖీ చేయడానికి మొదట నో-లోడ్ పరీక్షను నిర్వహించండి, ఆపై విచలనాన్ని నివారించడానికి హాయిస్ట్ యొక్క బెల్ట్‌ను మితమైన స్థాయి టెన్షన్‌కు బిగించి, ఆపై తనిఖీ చేయడానికి లోడ్ పరీక్షను నిర్వహించండి ఆపరేషన్ మరియు తెలియజేసే సామర్థ్యం, ​​ఏదైనా విచిత్రమైన శబ్దం మరియు కంపనం ఉన్నాయా, తనిఖీ చేయండి మరియు అడ్డంకులను తొలగించండి.
3. పిల్-ఇసుక విభజన:
మొదట రామ్ యొక్క కదలిక సరళంగా ఉందో లేదో తనిఖీ చేసి, ఆపై వేరుచేసే ప్లేట్ యొక్క సరైన స్థానాన్ని తనిఖీ చేయండి, ఆపై హాయిస్ట్ లోడ్ చేయబడి డీబగ్ చేయబడినప్పుడు, ఉక్కు షాట్ల యొక్క నిరంతర ప్రవాహం ఉంది, మరియు స్టీల్ షాట్లు బయటకు ప్రవహిస్తున్నాయా లేదా అని తనిఖీ చేయండి చ్యూట్ డిశ్చార్జ్ అయినప్పుడు
  • QR
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy